AvailabilityReliabilityManageabilityScalabilityspan>Routers encapsulate packets before _____. (Points : 2)after making a tagging decisionforwarding them to the egress interfaceforwarding them to the ingress interfacelearning about remote networksmaking a routing decision
A router learns a route from various sources. A network engineer is trying to determine which of the sources the router is using to make a routing decision. What would you tell the engineer? (Points : 2)Look at the lowest cost path.Look at the administrative distance.Look at the path with the lowest metric cost.Look at the path with the fastest bandwidth.A and C
What piece of information is included in theshow ip interface briefcommand? (Points : 2)The duplex mode of the interfaceThe next-hop IP addressThe Method used to assign the addressThe IP address of the ingress interfaceNone of the above
The process of forwarding network traffic from one VLAN to another VLAN using routing information is known as _____. (Points : 2)Inter-VLAN RoutingIntra-VLAN RoutingInter-VLAN RoutingVLAN RoutingIntra-VLAN communicationA and B
What is a disadvantage of traditional routing? (Points : 2)Does not support mutli-hop routingCan create layer-two loopsTransport too many VLAN-tagged packetsCan create layer 3 routing loopsAll of the above
The command used on a Cisco Catalyst 2960 switch to change the switched database manager (SDM) template is _____. (Points : 2)sdm changesdm usesdm prefersdm enableNone of the above
Which global configuration command must be entered before a connected PC could possibly automatically receive an IPv6 address and default gateway without using DHCPv6. (Points : 2)interface ip-addressipv6 global routingipv6 address enableipv6 unicast-routingNone of the above
Which command would you use to troubleshoot a routing problem between a router and a switch? (Points : 2)show interface ip briefdebug ip routeDebug interface ipshow ip protocolsshow ip route
A router is configured with the following commands.interface f0/2interface f0/2.10encapsulation dot1q 10ip address 192.168.10.254 255.255.255.0description Customer Services VLAN.interface f0/2.25encapsulation dot1q 25ip address 192.168.25.254 255.255.255.0description Sales VLAN.interface f0/2.50encapsulation dot1q 50ip address 192.168.50.254 255.255.255.0description Finance VLAN.endAfter installing the brand new router with the above commands users from all VLANs are unable to communicate. Assume this is only a configuration issue, what’s wrong? (Points : 2)The network engineer forgets to setup the duplex mode.The network engineer forgets to configure the clock rate.The network engineer forgets to enable the sub-interfaces.The network engineer forgets to configure routing.The network engineer forgets to enable the main Fast Ethernet interface.
A router is configured with the following commands.enableconfigure terminalinterface f0/1no shutdowninterface f0/1.20encapsulation dot1q 20ip address 192.168.10.126 255.255.255.192interface f0/1.25encapsulation dot1q 25ip address 192.168.10.254 255.255.255.192interface f0/1.30encapsulation dot1q 30ip address 192.168.10.62 255.255.255.192exitip address 0.0.0.0 0.0.0.0 s0/1/2endA packet with destination IP address 192.168.10.178 arrives on the above router’s interface. Which exit interface will the router use to forward the packet? Assume everything is working correctly. (Points : 2)       Fast Ethernet 0/1.10Fast Ethernet 0/1.15
Fast Ethernet 0/1.20Serial 0/1/2
This packet will be dropped.

Looking for a Similar Assignment? Order now and Get 10% Discount! Use Coupon Code "Newclient"