Overall instructions -Word document that includes:

·      a network

diagram using Visio,

·      an IPv4 subnetted addressing table,

·      a set of configuration listings (one per device configured),

·      a selection of diagnostic and discovery commands, and

·      a short, written summary answering the questions listed below. Be sure to verify spelling.

Specific directions:

1. This project is to be done individually.
2. Read through this entire assignment.
4. Start a new page.
5. Use Visio*to draw a small Local Area Network that consists of one router – with three interface, three switches – one connected to each router interface, and three PCs – each connected to one of the switches.  This is the basic layout:

Router

|                       |                      |

Switch 1           Switch 2         Switch 3

|                       |                       |

PC 1               PC 2                PC 3

1. Copy and paste your diagram on the second page of your Word document.

*Visio is accessible through iLab or via a free download from the Student Software Store

 

 

Continued next page…

1. Start a new page.
2. NOTICE! YOU ARE NOT TO USE THE AUTOMATED SETUP UTILITY FOR ANY OF THE CONFIGURATION PROCESSES!
3. need an IPv4 addressing scheme with subnets and VLANS for each of the three Router interfaces.
4. Use a publicclass C address of your choosing.
5. Subdivide (subnet) it into equalparts to support the 3 network segments. DO NOT USE THREE SEPARATE CLASS C ADDRESSES.
6. Add one VLAN to each subnet.
7. Complete Table 1 below according to your addressing and subnetting scheme. Copy the completed table into your report.

Table 1: Addressing Scheme

Device

Interface

IP Address

Subnet Mask

Default Gateway

R1

G0/1

G0/2

G0/3

S1

VLAN 15

S2

VLAN 25

S3

VLAN 35

PC-1

Ethernet 1

PC-2

Ethernet 1

PC-3

Ethernet 1

 

 

 

Continued next page…

Combine all previous work (with corrections) into one document and then add the remaining aspects of this project as follows:

1. Start a new page.
2. NOTICE! YOU ARE NOT TO USE THE AUTOMATED SETUP UTILITY FOR ANY OF THE CONFIGURATION PROCESSES!
3. For each of your seven devices, list all required commands needed to achieve a completely functional network. Include the following for each device:
4. Using Table 1 as a reference, for each device list the proper command-line syntax to:
5. Create the assigned name for the routers and switches. For example:

Router(config)#hostname R1

1. Create secure passwords at all levels (privilege mode, console, and vty) for the routers and switches. For example:

R1(config)#enable secret Password123

1. Assign the proper IP addresses with their correct subnet masks and default gateways. For example:

R1(config-int)#ip address 10.10.10.1 255.255.255.0

1. Create the VLAN management address for each switch with their correct subnet masks and default gateways. Refer to the table for the specific management VLAN designator.
2. Additionally, configure SSH on the router for security purposes.
3. Start a new page.
4. Write out the full command line syntax to:
5. Save the configurations for each network device (PCs excluded). For example:

S2#copy running-config startup-config

1. Verify connectivity from one PC through the network to the other PC (use two different commands ).
2. Display the saved configuration of the devices (PCs excluded).
3. Display the routing table on the router.

Remember!  Someone should be able to interconnect and configure all of the network devices using your diagrams and instruction scripts and have a fully functional network.

Continued next page…

 

Looking for a Similar Assignment? Order now and Get 10% Discount! Use Coupon Code "Newclient"

Given the diagram below. Assume the IPv6 prefix is 2005:007D:4500:000C::/64. Find the IPv6 EUI addresses for

computers A and B. Show all your work

 

Looking for a Similar Assignment? Order now and Get 10% Discount! Use Coupon Code "Newclient"